Which Stainless Steel Lug Nuts Work With Westlake Wheel and Tire Combo 274-000013

Question

Question:

Good morning what stainless lug nuts would be used for these rims including a set of wheel locks.Thank you have standard load rite boat trailer thx

asked by: Tim

1

Helpful Expert Reply:

The Westlake wheel and tire # 274-000014 you're looking at uses standard 60 degree cone lug nuts so you'll need (4) # KALN1375S per wheel, and (1) # RG01-150 per axle to get you up to 5 lug nuts per wheel total. The locks are Chrome as we do not sell any stainless locking lug nuts.

expert reply by: Samuel C

1

Answer 1

For lug nuts to go with your #LH37VR you want them to have the standard 60 degree cone and fit 1/2"-20 wheel studs. If you want a chrome-plated steel I recommend the #AM90049. For a stainless steel option you can use the #KALN1375S.

view full answer...

Answer 2

Yes the lug nut part #AM90070 would fit the Westlake ST205/75R14 Radial Tire w 14" Condor Aluminum Wheel - 5 on 4-1/2 - LR D - Gunmetal #LH37VR that you referenced.

view full answer...

Answer 3

The Westlake ST205/75R14 Radial Tire w/ 14" Wheel #LH37VR does not come balanced but this is certainly something you could have done at a local tire shop if desired. Typically though trailer tires don't need to be balanced like…

view full answer...

Answer 4

The recommended tire pressure is the max psi listed on your tire. For example, the Westlake ST205/75R14 Radial Tire #LH37VR has a max psi of 65 listed on the tire. This will be filled when the tire is cold.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Which Stainless Steel Lug Nuts Work With Westlake Wheel and Tire Combo 274-000013

Products Referenced in This Question

Continue Researching