Replacement Trailer Hub Grease Seal for Part Number 473317

Question

Question:

I need Spindle Grease Seal Sets for my tandem trailer. The axel set-up is outer L44649/L44610, Inner L68149/L68110,1.980 Bearing Buddy and currently has a National 473317 grease seal.

asked by: Ruben K

0

Expert Reply:

Thank you for the info you listed. Based on the seal number you mentioned the correct replacement is the part # 168233.

expert reply by: Jameson C

0

Answer 1

Yes, weight distribution shanks are pretty much universal so you can use can swap them out for one another across brands. The Curt Weight Distribution Shank part #C17131 is a great option which offers up to 3-1/4" of drop. I have attached a…

view full answer...

Answer 2

When the L68149 bearing is paired with the L68111 race, the 10-19 grease seal is used. However when the same bearing is used with the L68110 race on a boat trailer, the #168233 seal is usually used. You can verify this by using a digital caliper to…

view full answer...

Answer 3

I took a look at the replacement Converter for Parallax/Magnetek or WFCO RV Power Centers #PD4655V that you mention, and unfortunately it will not work with lithium batteries, and should only be used on flooded lead acid, AGM, and gel batteries.

view full answer...

Answer 4

Yes, both the Blue Ox tow bar wiring kit part #BLU79FR and the Curt trailer wiring kit part #56407 can install at same time on your 2023 Jeep Wrangler Unlimited and the order in which they install does not matter at all.

view full answer...

Answer 5

When your existing AD2527E grease seal is cross-referenced, the #168233 does show up as an appropriate replacement. Both seals have a 1.688 ID and a 2.332 OD. The #168233 would work just fine for you. I've linked to a demonstration video…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Replacement Trailer Hub Grease Seal for Part Number 473317

Product Page this Question was Asked From

Continue Researching