Parts Needed to Add Rails to Retrax Tonneau of 2010 GMC Sierra Short Bed for Yakima Overhaul

Question

Question:

Hey there. I have a 2010 gmc sierra slt crew cab short bed. My truck has a retraxpro bed cover on it. I’m trying to figure out what slotted rails I need so i can add the yakima ladder rack and keep my bed cover. Thank you.

asked by: Tyler N

0

Expert Reply:

For your 2010 GMC Sierra 1500 with a 5-1/2 foot bed and a RetraxPRO tonneau the rail kit you need is the part # RTX39FR which will give you ability to use a Yakima ladder rack like the OverHaul HD # Y01151-58 with the adapter part # Y01155.

expert reply by: Jameson C

0

Answer 1

You can use the Yakima 54" Tracks for Roof Racks #Y01127 without adding anything underneath. As far as protection, there is a plastic piece that will go in between the rail and the roof, so you don't have to worry about it damaging…

view full answer...

Answer 2

The correct hardware kit you need is going to be the Replacement Hardware Kit for TracRac SR Ladder Rack Base Rails part #752-186-3001 which works on both long and short bed models though you will have left over parts if you do have a short bed.…

view full answer...

Answer 3

To install crossbars on the Yakima 72" HD Tracks for Roof Racks #Y84MR you need 2 of the Landing Pad 26 #Y75ZR, the SkyLine Towers #Y53TR, and then your choice of Yakima crossbars. I recommend using the JetStream crossbars like the…

view full answer...

Answer 4

The only way to install the Yakima 60" HD Tracks for Roof Racks, OverHaul HD, and OutPost HD #Y74MR is with drilling. We do not have a different way to install these.

view full answer...

Answer 5

The TS (T-Slot) Rails for Truck Hero Elevate Rack System part #TH65FR for short bed or part #TH45FR will allow you to use a rack system on top of any tonneau cover that mounts inside the bed rails like the Retrax. This can then be used with the…

view full answer...

Answer 6

The Retrax PRO MX Tonneau Cover you'd asked about, part #RT80485 is a confirmed for for the 2020 Silverado 2500 long bed, as confirmed by my Retrax representative. The guides for the PRO MX are inboard of the bed sides, which will give the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...