Is Drilling Required to Install Yakima 60 inch HD Tracks Y74MR

Question

Question:

Is there any way to mount the Yakima HD Tracks without drilling into the boxsides? Can you attach via stake pockets? I would like to use the HD Track with a BAK Revolver X4s tonneau. Thanks.

asked by: John S

0

Expert Reply:

The only way to install the Yakima 60" HD Tracks for Roof Racks, OverHaul HD, and OutPost HD # Y74MR is with drilling. We do not have a different way to install these.

expert reply by: Jameson C

0

Answer 1

Absolutely! The Yakima OutPost HD Ladder Rack with Tracks #Y87KR is an excellent way to get a roof top tent on a trailer since it has standard-sized crossbars that have standard T-Slots on them which means you have multiple ways to mount various…

view full answer...

Answer 2

In order to install the Yakima 72" HD Tracks for Roof Racks, OverHaul HD, and OutPost HD #Y84MR on your vehicle you'd need to use a set of Yakima OutPost HD Overland Truck Bed Rack Uprights #Y01152. If you let me know what vehicle you're…

view full answer...

Answer 3

Yes, the CE Smith Coupler Lift Handle #CE32420 can be used on other trailers. The handle includes 2 sets of mounting holes for 3/8" or 1/2" hardware. If your trailer has a coupler that is attached to the frame using 1/2" bolts that are…

view full answer...

Answer 4

To secure your Hobie Mirage Pro Angler 14 with 360 Drive Technology to the lower level of the Yakima EasyRider Double Decker Trailer #Y08129 I recommend the Yakima BigCatch Kayak Carrier #Y04091. The BigCatch is confirmed to fit the lower round bars,…

view full answer...

Answer 5

It sounds like you have the Yakima HD crossbars similar to the #Y01156. These are attached and held in place by the HD Bar SL Adapter #Y03541 on your roof rack towers and the #Y03541 would be the correct way to replace one of those. The HD Bar SL…

view full answer...

Answer 6

To install crossbars on the Yakima 72" HD Tracks for Roof Racks #Y84MR you need 2 of the Landing Pad 26 #Y75ZR, the SkyLine Towers #Y53TR, and then your choice of Yakima crossbars. I recommend using the JetStream crossbars like the 50"…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 11

The Yakima EasyRider Double Decker Trailer #Y08129 is pretty well setup for off-road situations like you mentioned. It comes with shocks and decently aggressive tread tires so that it would handle moderate off-road scenarios like what most find…

view full answer...

Answer 12

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Is Drilling Required to Install Yakima 60 inch HD Tracks Y74MR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching