Is Convert-A-Ball Ball Mount # AMSC12 Compatible With Hitch Lock # 1469DAT?

Question

Question:

Hello! Help me please: Can a Convert-A-Ball Ball Mount AMSC12 and Hitch Lock 1469DAT be used together? Sincerely

asked by: Vladislav

0

Expert Reply:

Yes, the Convert-A-Ball Ball Mount # AMSC12 can be used with the Stainless Steel Trailer Hitch Lock # 1469DAT. The hitch pin is 5/8" in diameter to fit in your receiver with the ball mount.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 11

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 12

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Is Convert-A-Ball Ball Mount # AMSC12 Compatible With Hitch Lock # 1469DAT?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching