Can you Determine If a 2022 Subaru Ascent Has a Factory 7-Way Based On The VIN?

Question

Question:

Is there a way to tell if my 2022 Subaru Ascent came with the factory installed 7-way trailer connector? Like by VIn # or something?

asked by: Brian G

1

Helpful Expert Reply:

To determine if your 2022 Subaru Ascent came from the factory with a 7-way using the VIN, you will need to contact your Subaru dealer for a build sheet on your Ascent. If you have a factory 7-way you will be able to add a Redarc Tow-Pro Elite Brake Controller # RED63RR with a Adapter # 3062-P.

expert reply by: Bud M

1

Answer 1

To install the Redarc Tow-Pro Elite Brake Controller #RED44FR to the tow package on your 2022 Subaru Ascent you'll need to splice in the included pigtail to the factory wiring under your dash.

view full answer...

Answer 2

First you will need a Tekonsha Plug-In Wiring Adapter #3062-P to connect to the factory tow package wiring on your 2023 Subaru Ascent. This will allow you to connect to the Redarc Tow-Pro Elite Brake Controller for Tekonsha Harness #RED63RR. The…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 10

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...