Which Equal-i-zer Replacement L-Bracket Kit Fits 10k Rated WD System

Question

Question:

looking for replacement bracket or Equalizer 1,000 Max Tongue Weight 10,000 Max trailer weight. Will this fit?

asked by: Tina

0

Expert Reply:

The Replacement Equal-i-Zer Sway Control Bracket part # EQ95-01-5600 is the correct bracket replacement kit for an Equal-i-zer with a 10k trailer weight capacity like the # EQ37101ET.

expert reply by: Jameson C

0

Answer 1

You are correct that you want to be within the weight range of a particular system and that has to do with the total tongue weight. That includes the loaded trailer tongue weight along with any cargo behind the rear axle of your truck. You want the…

view full answer...

Answer 2

Trailer frame made of angle iron do not have enough surface area to safely attach snap-up brackets like those included with system #RP66542. But what you can do is use bolt on brackets #RP58305. You could get multiple sets of these for your trailers…

view full answer...

Answer 3

The Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW #C17500 is probably a good fit for your 2011 Tacoma and trailer with Jeep. For a weight distribution system, you want to use the loaded tongue…

view full answer...

Answer 4

I have attached photos showing the dimensions of the Replacement Sway-Control Bracket #EQ95-01-5600. The larger, L-shaped bracket measures 10 inches long x 2 inches wide and the smaller brackets measure 8-1/4 inches long x 1-1/2 inches wide. These…

view full answer...

Answer 5

With your trailer having a 7,000 pound rating, the Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 10,000 lbs GTW, 1,000 #C17500 may not be the best option for you. Typically the tongue weight of a trailer will be 10% of its…

view full answer...

Answer 6

Determining the correct rise or drop for your Blue Ox SwayPro Weight Distribution System #BXW1000 is going to be the same method as determining rise or drop for a standard ball mount. You will just need to measure from the ground to the top of your…

view full answer...

Answer 7

Since the bolt hole spacing is a standard 1-1/4 inches on center, you could certainly use the #BXW4000 shank in place of the one included with the #BXW1006 SwayPro system.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...