Replacement For Leaking Cable-Actuated Black Water Waste Valve

Question

Question:

I have a 2014 prime time crusader. Even when valve is closed on black water tank it leaks so expels when cap taken off. Right now I have the valterra add in gate valve. Which actuated gate valve would be the correct replacement and is this the correct fix? I have the valves in the compartment used for storage Thank you

asked by: Debra T

0

Expert Reply:

It is likely the correct fix yes, and the replacement cable actuated waste valve you need is the LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank - Spigot to Hub - 36" Cable # 34466N4AB36GM, 48" Cable # 34466N4AB48GMA, or 72" Cable # 34466N4AB72GMA.

To install it use LaSalle Bristol ABS Solvent Cement # 3447530889.

expert reply by: Kyle S

0

Answer 1

I don't know the length of the cable used for valves on your Montana so you'll want to measure the length to determine the correct replacement. To make the swap out easy I recommend just unbolting the old valve from the system and…

view full answer...

Answer 2

What I think you are asking is if you can replace within a current system, a valve assembly of one manufacturer with that of another. Yes, the fitment of valve assemblies is industry standard in dimensions. A Valterra 3" can be replaced with…

view full answer...

Answer 3

In order to fix your loose cable on your LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank #34466N4AB36GM, you will need to tighten the set screw that holds the cable to the valve stem. To do this. you're going to need to…

view full answer...

Answer 4

Thank you for the photos! Based on that it looks like you have a spigot to hub black water tank valve, like you mentioned, where the hub end fits over one pipe and the spigot end fits into the other pipe. So for a spigot to hub replacement valve…

view full answer...

Answer 5

You can try removing the screw, but I don't believe that's the issue. It sounds like your cable might be broken or the actual valve has just locked up or "frozen". There is currently not a replacement cable available…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

We still recommend the use of a slider in all standard/short bed trucks. That being said, the new GM trucks like your 2022 GMC Sierra 2500 do have a slightly longer bed than the typical standard bed. The best thing you can do is to measure to see if…

view full answer...

Answer 10

The newer Chevrolet and GM pickup trucks have a known power deficiency issue with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05. There is likely nothing wrong that you did, the problem is the…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

The best replacement pin box for the Lippert 1621 on your Grand Design Reflection 303RLS is the Curt Flex Air. This pin boxes has an air spring and shock absorber which will reduce the back and forth chucking (stopping and taking off) and lower the…

view full answer...