Pre-Greased Idler Hub that Fits Adams Boat Trailer

Question

Question:

I’m look for a pre greased hub assembly for my Adam’s manufactured drift boat trailer. Year is 2007. I have attached photos of the info off the trailer. It’s a 13” wheel with a 5x4.5 pattern I believe. Thanks for your help.

asked by: Billy

0

Expert Reply:

For your Dexter axle the pre-greased hub you'd want is the part # AKIHUB-545-2-LF-2K which has the 5 on 4-1/2 inch bolt pattern you need.

expert reply by: Jameson C

0

Answer 1

I spoke with an engineer from our hub manufacturer, Dexter, and they do not recommend using a hub for 8-12 inch wheels with a 13 inch wheel. However, they said that they do not make a hub for 13 inch wheels that has a hub flange diameter of smaller…

view full answer...

Answer 2

Thank you for providing that information. According to ShoreLandr your current hub uses #L44649 inner and outer bearings. That means you can use the Trailer Idler Hub Assembly for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased…

view full answer...

Answer 3

The Trailer Hub Assembly - 2,200-lb E-Z Lube Axle #8-258-50UC1-EZ that you referenced is a galvanized hub with the 5 on 4-1/2" bolt pattern. This uses inner and outer bearings #L44649 and has a 10-60 grease seal with a 1.50" inner diameter…

view full answer...

Answer 4

The Dexter Trailer Hub part #8-258-50UC1-EZ that you referenced is sold individually. If you needed two of these you'd have to order a quantity of 2.

view full answer...

Answer 5

It sounds like you have a 2,000 lb axle on your 1997 Shoreline Boat Trailer. I'm also assuming you have a 5 on 4-1/2 bolt pattern since you were looking at the #AKIHUB-545-2-LF-2K. In order to make sure you choose the right hub assembly you are…

view full answer...

Answer 6

It sounds like you're looking for the Trailer Idler Hub Assembly for 2K Axles part #AKIHUB-545-2-LF-2K which has a 5 on 4-1/2" bolt pattern and uses two L44649 bearings. This is designed for a 2,000/2,200 lb axle which if this is your…

view full answer...

Answer 7

Even though you do not have EZ lube axles you will be able to add EZ lube hubs and drums, however, you will not have the EZ lube feature on his axles by installing the EZ lube hub and drums. For you to be able to easily pack grease into your hubs and…

view full answer...

Answer 8

We have just the hub you are looking for with the part #AKIHUB-545-2-EZ-2K. This matches the bearing and seal info you listed, the bolt pattern, has an ez-lube cap for access to the grease fitting, and comes pre-greased so it's ready to install.…

view full answer...

Answer 9

We offer both of the trailer tire sizes you mentioned, ST175/80R13 and ST185/80D13. In terms of size they are very close to one another; the ST175/80R13 size measures 24.1-inches in diameter and 6.9-inches wide while the ST185/80D13 size measures…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...