Correct Replacement Lift Strut for 2005 Chrysler Town and Country Rear Hatch

Question

Question:

I have a 2005 Chrysler town and country mini van I need the shock that opens the tailgate when you push the button on the key fob

asked by: Jon N

0

Expert Reply:

The correct liftgate support shock for a 2005 Chrysler Town and Country is the Liftgate Lift Support part # ATL64RR which will be a direct replacement for your existing. The installation is very easy as well, simply thread the old fittings out on each end and then repeat the same process in reverse for the install.

expert reply by: Conner L

0

Answer 1

We offer D-ring tie downs like the bolt-on Brophy #SR15-C and the weld-on Curt #J-705 that can be seen on the linked page. For one close to your measurements you might consider the Brophy #LRB1 which is also a bolt-on part whose dimensions are shown…

view full answer...

Answer 2

The Gas Shock #372-7901 you were looking at would attach to a 10mm ball stud, but I have no way of knowing if the shock in your photo would connect to 10mm ball without physically testing it.

view full answer...

Answer 3

The wires for the Replacement Wiring Harness for Lippert Slide-Out Controller #LC135696 are 7-1/2" in length and the connector is 1-1/16" in length.

view full answer...

Answer 4

No, you would not be able to. I have spoken with Furrion about this exact question before because their written specifications are misleading. The 14,500 BTU Furrion Chill Replacement RV Air Conditioners, like the item #FR66SR you were looking at,…

view full answer...

Answer 5

Sealant isn't required when installing the Rubber Wiper Seal and Bulb for RV Slide Out #SR68FR, but I would put a few screws in to help hold the seal since the trailer will bake in the sun and can cause issues with the 3M tape. At minimum I would…

view full answer...

Answer 6

Manufacturers do not have a list available for the public to see exactly what motor was used on your 2006 Fleetwood Expedition so I would need to parts number listed on the motor to determine the correct replacement. I've attached a picture below…

view full answer...

Answer 7

I went out to the warehouse and pulled hanger kit #APS1 to measure the hangers for you. The larger hangers measure 3 inches long, 2-5/16 inches wide, and 2-1/8 inches tall overall. The smaller hangers are 2-1/8 inches long, 1-13/16 inches wide, and…

view full answer...

Answer 8

Unfortunately, I have no way to look up what parts are installed on your 2009 Heartland North Country. You may be able to contact the RV manufacturer with your VIN number to determine if they kept record of this when they manufactured the RV.…

view full answer...

Answer 9

To find the correct slide out seal for your 2002 King of the Road Royalite 34RBW you will first need to identify what you have. Remove a portion of the seal to get the side profile of your current seal. Then, measure the length. While doing this you…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Correct Replacement Lift Strut for 2005 Chrysler Town and Country Rear Hatch

Product Page this Question was Asked From

Continue Researching