What Are The Dimensions of the Vertical Holes on the Flash Solid Steel Adjustable 2-Ball Mount?

Question

Question:

I need to know the diameter of the adjustment holes and the distance between holes. I want to use my current ball with this and I need the holes to be 1 inch in diameter and 1/2 inch apart.

asked by: Dennis W

0

Expert Reply:

The Flash Solid Steel Adjustable 2-Ball Mount # FA49-00-5900 uses a 5/8" diameter pin to secure the ball mount to the adjustable shank. These holes are spread 1" on center vertically along the shank. As these do not match the information you sent if you can tell me what parts you have I can determine if there is a system which will fit your current ball you want to also use.

expert reply by: Bud M

0

Answer 1

From the pin hole to the center of the ball hole on the Flash Solid Steel Adjustable 2-Ball Mount part #FA49-00-5900 measures 9 inches. So if you measure from the pin hole of your hitch out to the furthest point out on the rear bumper and it's…

view full answer...

Answer 2

The Convert-A-Ball Cushioned Ball Mount for 2" Hitches #AMSC12 referenced in your question can be safely installed and used in an upright or upside-down position in order to provide the needed drop or rise. To get the 10-3/4" rise from the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 9

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

What Are The Dimensions of the Vertical Holes on the Flash Solid Steel Adjustable 2-Ball Mount?

Product Page this Question was Asked From

Continue Researching