Replacement Mounting Brackets For Carr Super Hoop Custom-Fit Side Steps # CARR124031

Question

Question:

I have the super hoop 124031 model on my van. Will these brackets work.

asked by: Darrin H

1

Helpful Expert Reply:

The Replacement Mounting Brackets # CARRBR14702K2 will fit the Carr Custom-Fit Side Steps # CARR124031 on your van.

expert reply by: Bud M

1

Answer 1

Yes, the Replacement Mounting Brackets for Carr Custom-Fit Side Step part #CARRBR14702K2 will work with the Super Hoop XM3 Side Steps which I confirmed with my contact at Carr for you.

view full answer...

Answer 2

I checked with Curt and the distance between the vertical mounting flanges of the Curt #C15300 is 33.312 inches.

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #C15300 which is a fit for a 1977 Ford F-250 is designed for the factory gas tank. If you have an aftermarket gas tank then we would not be able to confirm fit but what I could do is provide you with the inner…

view full answer...

Answer 4

Center hole to center hole, the distance apart for all three holes measured from the holes on one flange across to the other is 43-5/8 inches. The flanges measure 41-1/8 apart, measured inside to inside and the 3 holes along each flange are 3-1/2…

view full answer...

Answer 5

I would be happy to help you. I have linked some diagrams with every dimension you will need. The Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2" item #C15300 is confirmed to fit a 1979 Ford Bronco.

view full answer...

Answer 6

In regards to the etrailer Trailer Hitch Receiver part #e75ZR for a 2023 Toyota Highlander, you must trim the underbody panel per the manufacturer. The hitch will come into contact with the panel if not trimmed. The panel however does not need to be…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Mounting Brackets For Carr Super Hoop Custom-Fit Side Steps # CARR124031

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching