What Locks Will Fit MaxxTow Adjustable-Height Ball Mount MT70067

Question

Question:

What locks are available for MT70067 hitch. I want to be able to lock the whole assemble to my RV so no part of the hitch can be removed without a key.

asked by: Jamie

0

Expert Reply:

To secure both the shank and ball platform portions of the MaxxTow Adjustable-Height Ball Mount MT70067 to your RV you can use two of our Hitch Receiver Locks # e98881.

The # e98881 provides an extra wide center span of 3-5/8-inches, which is more than enough to comfortably fit the 2-5/8-inch outside dimension of the MaxxTow ball platform. To secure the 2-inch shank portion to your receiver you will use a second unit.

Multiples of these locks are available keyed alike for convenience for a nominal charge. When you place your order online simply indicate a quantity of 2 and select the Keyed Alike option from the drop-down menu.

expert reply by: Adam R

0

Answer 1

Thank you for providing a photo of your trailer coupler. Trailers should always be level when hitched. If a trailer is out of level when towed it will tend to have more sway. I notice you have weight distribution (WD) lift brackets on your trailer…

view full answer...

Answer 2

That foot pound rating for torqueing a hitch ball onto a ball mount requires a special torque wrench. A local mechanic should have something compatible. If you can't find anyone with the correct torque wrench as many max out at 250 lbs, then we…

view full answer...

Answer 3

The #e98881 lock you referenced is a fit for Class III, IV and V hitches. It is intended for use as a hitch lock, to deter theft of a ball mount or other hitch mounted accessory. The receiver tube of a Class V hitch is typically about 3-1/2 inches…

view full answer...

Answer 4

Hitch pins like #C23556 do not have a weight rating or shear strength data because their actual capacities far exceed the abilities of the hitch or vehicle. Basically, the hitch or some other component would fail before the pin even comes close. The…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

What Locks Will Fit MaxxTow Adjustable-Height Ball Mount MT70067

Product Page this Question was Asked From

Continue Researching