Pigtail Harness for Propane System Between Regulator and Tank

Question

Question:

Im looking for the propane hose that goes from the tanks to the regulator on my food truck

asked by: Bryan E

0

Expert Reply:

Sounds like you are looking for a pigtail hose for your propane system like the # 100473-24-MBS which is 2 feet long. This is what normally connects between the tanks and the regulator. If you need a different size check out the link I attached that has all of the pigtails we carry.

expert reply by: Jameson C

0

Answer 1

Typically most 2-stage regulators like the #CAM59323 will have a 1/4" NPT inlet connection which would allow you to connect a POL fitting like #37207-30085 to connect to the inner threads of the 20lb tank. If this is what you have and you're…

view full answer...

Answer 2

I understand what you are saying and I think you are on the right track. A bit more length from the pig tail would allow the rubber line to be able to loop so that it could tuck down better. We have 15 inch pig tails like part #100473-15-MBS or even…

view full answer...

Answer 3

The connection needed to the propane is a type 1. I recommend the MB Sturgis Propane Pigtail - Stainless Overbraid, #100833-24 with a Type 1 fitting that has an internal back-check and your needed 1/4" male inverted flare. We also have the MB…

view full answer...

Answer 4

If you can send me a picture of the pigtail you're trying to replace or the inlet on your regulator I can confirm this, but it sounds like you need a pigtail with an NPT fitting as opposed to the Male Inverted Flare. The NPT pigtail which matches…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 12

I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…

view full answer...