Replacement Idler Hub Needed for 2,000 lb Trailer
Question:
So I am looking for a 3/4 inch idle trailer hub replacement. Do you have any of those available? It is for a 2000lb trailer.
asked by: Juan
Expert Reply:
The closest that we have for your application is the Idler Hub # AKIHUB-440-2-EZ-1K with a 4 on 4" bolt pattern or the # AKIHUB-545-2-EZ-1K which a 5 on 4-1/2" bolt pattern. These are designed for a 1" spindle which is the standard for a 2,000 lb trailer axle.
If you truly have a 3/4" spindle diameter then you're going to be looking at an older setup for something that's really hard to come by so my recommendation would be to change out your axle to something with modern specs so it's easier to maintain in the future.
Attached is a link to our selection of 2,000 lb axles which includes standard types that you have to measure the spring center and hub face measurements for a replacement or you could use the specialty Timbren Axle-Less Trailer Suspension System # ASR2000S01 which bolts right to the trailer frame.
Attached is a review and installation video of the Timbren system for you to check out.
Products Referenced in This Question
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 10" to 12" - 5 on 4.5 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- Pre-Greased
- L44643
- L44643
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 2,000 lbs
- Trailer Axles
- Rubber Spring Suspension
- Easy Lube Spindles
- No Hubs
- 2000 lbs
- Spindles Only
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- L44643
- L44643
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Tire Sizing
- Article: Most Popular Wheel Bearings
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: 4-Way Trailer Wiring Recommendation for 1993 Ford E-350 Van
- Q&A: Measuring For Replacement Idler Hubs On a 1997 Scamper 23L Pop Up Camper
- Q&A: What is the Difference Between Load Range B and C Trailer Tires
- Q&A: Length of Replacement Handle with Claw Knob for Square Jacks
- Q&A: Availability of ST205/75R14 Trailer Tires In a Load Range E or F
- Q&A: Replacement Hub and Drum Assemblies for AL/KO 8460 Hubs and Drums
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Routing the Power Wire for a Trailer Wiring Harness