Availability of B and W Gooseneck Hitch Cover that Can Fit Square Hitch Hole

Question

Question:

Hello, I bought a truck that had a gooseneck ball in the bed. When I pull this ball out I know have a hole that Im wanting to cover. The ball that came out is square. I have looked everywhere for a cover to put in this hole. Do you guys sell this part? Thanks,

asked by: Tim A

0

Expert Reply:

The B&W Rubber Cover for Empty Turnoverball Socket # BWGNXA1715 is designed to fit a square gooseneck hitch hole. This cover is designed to fit a 2-1/2 inch square hole so you might measure what you have now to see if this would fit or not.

expert reply by: Jameson C

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

The correct tie-downs for your 2019 Ram 3500 Tradesman short bed depend on your hitch. You can choose from the following: With a factory installed hitch or non-Torklift aftermarket hitch -TorkLift Talon Camper Tie-Downs #TL52XR (front) and #TL34FR…

view full answer...

Answer 10

Hey Mark, from previous customers we have determined that the your 2009 Coachmen Chapparal M-278 has a Lippert 1621 pin box so the Gen-Y Gooseneck adapter part #GY58GR would fit and work great on it. This will give you a cushioned gooseneck adapter.…

view full answer...

Answer 11

Hey Parvez, glad I could help! So the Rhino Rack Vortex Crossbars for Retrax XR tonneau covers part #RRVA180B-RRRLT600 was designed specifically to work with your RetraxOne XR tonneau cover so it is going to definitely have enough clearance above…

view full answer...

Answer 12

Yes, you can use 2 of the Timbren Axle-Less Trailer Suspension Kits #ASR35HDS02 which will give you a total trailer GVWR of 7,000lbs. Do understand you must include the weight of the trailer into this calculation. If you are needing to carry 7,000lbs…

view full answer...

Availability of B and W Gooseneck Hitch Cover that Can Fit Square Hitch Hole

Product Page this Question was Asked From

Continue Researching