Is There a Drop Leg Attachment for the Trailer Valet JXC Trailer Jack

Question

Question:

Does the JF-1005H-Z leg fit a Trailer Valet JXC jack?

asked by: Dallas I

0

Expert Reply:

I do have an option for you but there isn't a drop leg available for the Trailer Valet JXC Trailer Jack part # TV54FR or part # TV94FR. If you're after faster operation or less work then you may want to take advantage of the drill powered operation using the Drill Attachment part # TVDA. The other option is to simply go electric using the Electric Jack w/ Footplate part # EJ-3527-BBX which has the same benefits as using the drill attachment but with a lot less parts.

expert reply by: Conner L

0

Answer 1

The etrailer A-Frame Round Jack #TJA-5000S-B is a great sidewind jack. It is rated for 5,000lbs capacity and will extend to 24" below the mounting bracket. The Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter…

view full answer...

Answer 2

The Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option, #TV94FR is a replacement. You will need to remove the Braber BE-130 Jack. The Trailer Valet, #TV94FR has an outer tube diameter of 2-1/4". My suggestion is to measure the…

view full answer...

Answer 3

The highest capacity trailer tire we offer that fits a 14 inch trailer rim is the Load Range D part #TTWTRTM2157514D which has a capacity of 2,200-lb max load at 65 psi. With trailer tires you have to keep them inflated to their max psi at all times…

view full answer...

Answer 4

Yes, you can replace your load range C tires with load range D tires without issue. It will only become any issue when you go down load ranges, not up. The tires will have the same overall diameter as long as they are the same size regardless of…

view full answer...

Answer 5

I'll start out by saying that the Goodyear Endurance tires that we carry are all radial tires, but we do not have any available in a 205/75R15. However, if you're looking for a bias ply tire with those measurements I recommend using the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...