Recommended Replacement for Atwood RV Propane Gas Detector 31013

Question

Question:

I have an Atwood propane detector, black, MODEL LP_DOB PART# 31013. I understand it has been discontinued. Id rather not cut new holes. what would be the replacement?

asked by: John W

0

Expert Reply:

The RV Propane Gas Detector part # RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a super clean install when finished. You'd just need to use some butt connector like part # DW05744-5 to attach the wires and you're good.

expert reply by: Conner L

0

Answer 1

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 2

We've seen this issue before on your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 and the beeping every 40 seconds indicates "a fault has been detected that compromises some detector function." What you need…

view full answer...

Answer 3

The RV Propane Gas Detector part #RS64FR for white or part #RS44FR for black is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you…

view full answer...

Answer 4

The closest option to your Atwood 31013 is going to be the Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681. This propane detector requires a 3-9/16" long x 3-7/16" wide x 1" deep cutout hole in order to fit and…

view full answer...

Answer 5

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

Answer 6

The Atwood 31013 is no longer made. The best choice for replacement is the RVCO #RS34FR which mounts flush against the wall, and the overall measurements are 4-1/4" square, and it sticks out 1/2" from the wall. Works with 2-wire…

view full answer...

Answer 7

While we don't have an exact fit for your current detector's cutout hole I do still have an option for you with the RV Propane Gas and Carbon Monoxide Detector - Black #RS54FR (white #RS34FR). This detector is a surface mount design that…

view full answer...

Answer 8

Atwood is no longer in business so you'd have to switch over to a new brand in order to get what you need. We currently only carry the RV Propane Gas #RS44FR (white #RS64FR) which comes with two different trims (large: 7-1/4" long x…

view full answer...

Answer 9

The blocks you're referring to in the #LC26VR kit are called "Flat back rack plugs" and are used to close the holes up on either end of the track. This just prevents water, bugs, etc. from getting into the opening of the track and…

view full answer...

Answer 10

The piece you're referring to in the #LC26VR kit is called a "shoe". This part is plastic with foam pads on each end that helps cushion the motor bracket as it slides back and forth to either end of the track.

view full answer...

Answer 11

We do have some LP gas detectors available, but none would be a direct replacement for your CCI 7770.2 / Pre Tell 22. From what I could find on your CCI 7770.2 / Pre Tell 22, it has dimensions of 6.25" wide x 3.9" tall. The RV Propane Gas…

view full answer...

Answer 12

I recommend the #RS34FR to replace your current LP gas detector. This is a simple 2 wire design making for easy installation.

view full answer...

Recommended Replacement for Atwood RV Propane Gas Detector 31013

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching