How to Determine Correct Dexter Axle Over-Under Conversion Kit

Question

Question:

Will your K71-385-00 fit this dexter axle 7194651

asked by: Daniel

0

Expert Reply:

If your Dexter Axle has a 3" diameter and the leaf springs are currently below your axle then the Over-Under Conversion Kit # K71-385-00 will work. If your axle diameter is 2-3/8" instead then you'll need the Over-Under Conversion Kit # K71-384-00.

I'm not able to confirm what size our axle is from that part number but you'll be able to confirm which kit you need by simply measuring your axle diameter.

Attached is an installation video for you to check out.

expert reply by: Jon G

0

Answer 1

I do have an option for you but the Lippert Components Bolt-On Shock Kit like part #LC281281 is designed for use on overslung axles (leaf springs over axle) only. Therefore, it should not be used with the underslung (leaf springs under axle) axles…

view full answer...

Answer 2

Some trailers do have shock absorbers; it isn't all that common but is gaining popularity, mostly among camping trailers. The main reason it's not too common is most people aren't worried about the ride being that smooth. Usually the…

view full answer...

Answer 3

The trailer lift kit options really come down to the axle type and setup. For leaf spring axles, you can either flip the axles with a kit like part #K71-384-00 or part #K71-385-00 or you can raise the hangers/shackles with a kit like part #LC425750.…

view full answer...

Answer 4

I can tell you how to easily determine the correct over/under conversion kit for your 2017 K-Z Sportsmen Classic 180THT, though we would not be able to verify a specific fit for any trailer. It's easy to determine the correct over/under lift kit…

view full answer...

Answer 5

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 6

Yes, you can use the over/under conversion kit #K71-385-00 to move the axles to the tops of the leaf spring stacks. Dexter has the following note on the conversion kits: When converting from underslung to overslung, the installation of bump stops to…

view full answer...

Answer 7

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit and…

view full answer...

Answer 8

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 9

Dexter Trailer Springs Over-Under Conversion Kit, part #K71-384-00, is specified by Dexter for use only with double-eye springs. It is not suitable for use with slipper springs. It is considered by our technical friends at Dexter to be unsafe to use…

view full answer...

Answer 10

I have checked the installation instructions for the Dexter Trailer Springs Over-Under Conversion Kit #K71-385-00, and according to Dexter they strongly recommend tack welding the spring seats in place. Please note that this kit is intended for use…

view full answer...

Answer 11

Yes when you do an over-under kit you have to weld the seats to the axle for it to be installed properly. It is recommended to tack weld the new spring seats into place but a complete weld job is not required when installing the over-under conversion…

view full answer...

Answer 12

First, thank you so much for providing all the axle information on your 2007 Fleetwood Redline 33. The 4-Leaf Double-Eye Spring #e47SR is our closest match to the Lippert 702096 leaf springs that came on your trailer. You will want to order 4 of…

view full answer...