Availability of Extra Nuts for 1/2" Wheel Studs on Dexter Hub and Drum Assembly

Question

Question:

If I want to order extra nuts which part number is it?

asked by: Jonathan G

0

Expert Reply:

For extra nuts that will fit the wheel studs on the # 8-219-4UC3 you can use the CE Smith Trailer Wheel Lug Nut # CE11051. These will fit the 1/2" wheel studs on the hub and drum assembly.

expert reply by: Robin H

0

Answer 1

The Dexter Trailer Hub and Drum Assembly #8-219-4UC3 comes with 1/2" wheel studs. For extra wheel studs you need the Trailer Hub Wheel Stud #7-122. If you need extra wheel lug nuts you can use the #CE11051.

view full answer...

Answer 2

You are correct, the #8-219-4UC3 matches your existing hub and drum assembly. I'm assuming you're referencing the difference in the grease cap when you say the grease is different. This has a standard grease cap, but you can use your…

view full answer...

Answer 3

You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch, 1.986…

view full answer...

Answer 4

Trailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like #CE11051, but a 90-degree like #STN569 is also available for 9/16-inch studs.…

view full answer...

Answer 5

We have many styles and sizes of trailer wheel lug nuts shown on the linked page. These are offered in either 60-degree or 90-degree coned profile, in zinc, chrome or stainless and for four different wheel stud diameters. Just click on the feature to…

view full answer...

Answer 6

There are common lug nut sizes found on trailers: 7/16, 1/2, 9/16, and 5/8 but the most common is 1/2 inch. If you can tell me the trailer weight capacity and wheel size/bolt pattern I can verify if they are likely to be 1/2 inch or another size. If…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Availability of Extra Nuts for 1/2" Wheel Studs on Dexter Hub and Drum Assembly

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching