Replacement Switch For An Atwood MPD 93756 Water Heater

Question

Question:

Is this rocker switch/light compatible with an atwood MPD 93756 Hot water heater? Looking to replace 4-prong switch in 2005 R-vision Trail Lite Bantam trailer. Old switch is similar and is a Carling 0323 switch when i pull it out of the housing.

asked by: Jeff C

0

Expert Reply:

Yes. you can use the Single-Panel On/Off Switch for Atwood Gas and Electric Water Heaters # AT91859 with your Atwood MPD 93756 water heater.

We have this switch available in black if you're interested # AT91959.

expert reply by: Bryce D

0

Answer 1

Since you don't have the wiring harness on your previous RV water heater you most likely had an all propane powered unit. The Atwood RV Water Heater w/ Heat Exchange - Gas and Electric - Automatic Pilot - 8,800 Btu - 6 Gal #AT96163 is powered by…

view full answer...

Answer 2

Usually air conditioners and refrigerators draw more power than just 9 amps, especially when they initially kick on. The added draw of Camco Propane to Electricity Converter #CAM11673 could cause that circuit to blow/trip in certain situations so the…

view full answer...

Answer 3

I have attached for you the wiring part of the install instructions for the Camco Propane to Electricity Converter for 6-Gallon RV Water Heaters part #CAM11673 below.

view full answer...

Answer 4

My awning contact at Lippert advised that the very first thing to do before you try to install the Carefree awning you have purchased is to contact the maker of the trailer with its VIN to confirm that the internal construction is able to handle the…

view full answer...

Answer 5

Yes, the temperatures you mentioned are normal. If you were getting over 200 degrees that would be a bad sign. But typically if all of the hubs are the same temperature you're good and it's only really an issue if one of the hubs is hotter…

view full answer...

Answer 6

You might have one brake that's adjusted tighter than the other. That's really the only thing I can think of that would cause one hub to get hotter than the others when brakes are applied. You want your brake controller to be set so that it…

view full answer...

Answer 7

We do not have any way to know where an individual switch is located on a trailer; the best we can do is offer a replacement switch. For a single-panel switch you would need the Replacement Single-Panel On/Off Switch for Atwood Gas and Electric Water…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Replacement Switch For An Atwood MPD 93756 Water Heater

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching