Does U-Bolt of Aero Crossbar Fit Kit S280 Fit Around Yakima Jetstream Crossbars

Question

Question:

Im building a custom platform that will go onto of my Yakima jet stream bars. Will this clamp fit around the bars?

asked by: Zane W

0

Expert Reply:

Yes, the Aero Crossbar Fit Kit for Rhino-Rack Steel Mesh Baskets and Steel Mesh Trays # S280 that you referenced does fit around the Yakima Jetstream crossbars.

expert reply by: Jameson C

0

Answer 1

You seem to have an older thule cargo box which they do not make anymore. If you're not wanting to get a new box you will have to rig something up to get the box to work with your bars. You will have to drill out one hole and use an existing hole…

view full answer...

Answer 2

I went out to the warehouse and took some measurements of the Replacement Plate Box Support, #TH10378. The center to center distance between 2 adjacent holes is 2 inches (5cm). The center to center distance between the 2 outside holes is 4 inches…

view full answer...

Answer 3

The threaded portion of the u-bolts in the RhinoRack Crossbar Fit Kit, part #S280, measures 1-1/8 inches. This kit consists of 4 u-bolts, 8 plastic knobs with threaded steel inserts, 8 washers, 8 plastic caps for ends of the u-bolts, and 4 metal…

view full answer...

Answer 4

I am not aware of any direct fit mounting hardware kits available for the Sears X Cargo Roof Mounted Cargo Boxes due to their age. As you mentioned, you will need to drill holes in order to mount it onto a set of crossbars. The u-bolts kits are…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Does U-Bolt of Aero Crossbar Fit Kit S280 Fit Around Yakima Jetstream Crossbars

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching