Bulldog Winch and Mounting Bracket For a 2019 Toyota 4Runner

Question

Question:

I see a Bulldog hidden wench bracket for a 2019 3rd Gen Tacoma but I’m looking for a 5th Gen 4Runner. Are these the same mounts?

asked by: Liz

0

Expert Reply:

I have a couple options for you as the Bulldog Winch Off-Road Winch Mounting Plate for Toyota Tacoma Gen III # BDW23001 is only confirmed to fit the Gen 3 Tacoma and they do not have a separate plate for your 2019 Toyota 4Runner.

First you can have a custom mounting plate created using the Universal Mounting Plate # BDW20291. This will need to be completed at a fabrication facility near you.

Or you can use the Bulldog Winch Receiver Mount Kit # BDW20155 with a front mount receiver. There are different receivers for your 4Runner based on your trim level.

Draw-Tite Front Mount Trailer Hitch Receiver # 65074(SR5, TRD)
Curt Front Mount Trailer Hitch Receiver # C31076(SR5, TRD, Limited)

I recommend the Bulldog Winch Trailer Winch # BDW10040 for use with your 4Runner. This allows you to control the winch with a wireless remote and uses a much safer synthetic rope over a wire cable.

expert reply by: Bud M

0

Answer 1

The only place to install a front mount hitch on your 2016 Toyota 4Runner is under the front bumper fascia which means you will lose a bit of ground clearance. That said, the hitch will be pretty much level with the belly pan so this can also be…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, your 2017 Chevrolet Equinox FWD can be flat towed with all 4 wheels on the ground. Do understand that you will need to run your Equinox for 5 minutes every time you stop for gas to properly lubricate your transmission and before towing. A better…

view full answer...

Answer 4

It sounds like you have a 7-way blade connector on your boat trailer as that is a very common connector on boat styles. This connector has 6 pins around the outside of the connector and a center pin for a total of 7. Part #A7WCB would be what a 7-way…

view full answer...

Answer 5

We do offer tow bar setups that can attach to the D-rings on the Warn Elite Bumper. Your will need to use a D-ring adapter to connect the tow bar. For the adapter you have the following options: 1" Thick D-Rings #RM-035-1 3/4" Thick D-Rings…

view full answer...

Answer 6

While Bulldog does not have a different winch mount for your 2020 Tacoma TRD Off Road, we do have reviews(see images) of the Bulldog Winch Off-Road Winch Mounting Plate for Toyota Tacoma Gen III 2016 to 2019 #BDW23001 being installed on a 2020 and…

view full answer...

Answer 7

If you're looking for a Jerry can holder to go with a basket, that limits what you can mount to your roof. We don't carry can holders that are compatible with baskets like the OffGrid, part #Y07138. Instead, you can use the Yakima LockNLoad,…

view full answer...

Answer 8

Thanks for the picture! I reached out to my contact at Lippert and you will need the replacement motor #LC183058 which will be a direct replacement for the HappiJac 70425-004.

view full answer...

Answer 9

Yes the Smittybilt winch you mentioned would fit on the Bulldog Universal Mounting Plate for Trailer Winches part #BDW20291 that you referenced.

view full answer...

Answer 10

The Bulldog Winch Hitch Mounted Winch Mounting Plate with Handles #BDW20011 is a pretty universal fit but I have some things for you to double check with your Ramsey RE12000 winch prior to using this for your winch as I wasn't able to find any…

view full answer...

Answer 11

The Curt front mount receiver, #31313, is a front mount receiver. You can also call it a trailer hitch even though it is at the front of the vehicle and not the back. As far as installation notes for this hitch, I show that no drilling is required or…

view full answer...

Answer 12

If you'll look at the provided customer review by Mike H, you'll see that he was easily able to reinstall skid plate after the Curt #31313 Front Mounted Receiver was installed on his 2008 Toyota Tacoma. No modifications were needed. I've…

view full answer...

Bulldog Winch and Mounting Bracket For a 2019 Toyota 4Runner

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching