Power Gear 500210 Replacement Touch Pad Control Unit

Question

Question:

Have a touch pad 500212 for Power gear leveling for 1996 fleetwood discovery motorhome. Looking to see if that is the same you sell. Mine is 2.5 inches by 5.5 like one you had with 8 wire and 6 wire and a none used 2 wire thank you.

asked by: Steve S

0

Expert Reply:

I believe you meant to type that your touch pad was part number 500210 which the Replacement Key Pad Control Unit for Power Gear Powered RV Leveling System # LC82FR is a correct replacement for.

expert reply by: Jameson C

0

Answer 1

Are you only installing the #LC82FR (500731)? To replace your 500210 you will need the full kit #LC359259. There are also wiring changes you will have to make at the pump assembly before it will work. After speaking with Lippert it sounds like this…

view full answer...

Answer 2

I found an old wiring diagram for your now discontinued Power Gear 500210 control panel and it really helps show how things are supposed to work. There is a red wire running to the three jacks, the dump valve, and the float valve from the solenoid.…

view full answer...

Answer 3

The correct replacement keypad for your Power Gear leveling system that used the 500731 keypad/controller is part LC359403 which we offer as part #LC82FR. Lippert has confirmed that this is the correct replacement.

view full answer...

Answer 4

Yes, The Replacement Key Pad Control Unit for Power Gear Powered RV Leveling System #LC82FR is the correct key pad control unit you will need per Lippert for your 1998 Chevy Southwind Storm Motorhome using the 500210 Milwaukee cylinder board. I…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Power Gear 500210 Replacement Touch Pad Control Unit

Product Page this Question was Asked From

Continue Researching