Trailer Hitch For A 2002 Ford Ranger With Step Side Bed
Question:
My 2002 ranger has the step side bed, will this still fit? Having a hard time finding fitment specs for the step side beds.
asked by: Daniel B
Expert Reply:
Yes, The Curt Trailer Hitch Receiver # 13138 is confirmed to fit your 2002 Ford Ranger with step side bed.
The trailer hitch has a bolt-on installation with no welding required. It has a gloss black powder coat finish that is over a protective base coat that offers a superior rust resistance.
The trailer hitch has a maximum gross trailer weight up to 4,000 pounds and has a maximum tongue weight up to 400 pounds. I would recommend checking your vehicle's manual to find out the proper towing capacity of your vehicle.
The T-One Vehicle Wiring Harness # 118344 will give you a 4-flat connector and make it to where the trailer's stop, turn, and taillights will mirror your vehicle's stop, turn, and taillights. This harness will plug into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove either the tail light assemblies or the interior trim panels to access this harness.
It is recommended that you use a small amount of grease # 11755 on all electrical connections, the plugs on your vehicle, and the 4-pole connector itself to help prevent corrosion.
The Curt Towing Starter Kit # C45554 includes an 8-1/4 inch long, powder coated ball mount with a pre-torqued hitch ball; hitch pin and clip; hitch receiver lock with keys; hitch cover; and a storage case.
I attached an installation video link below.
Products Referenced in This Question
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 2 Inch Ball
- One Ball
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- Pre-Torqued
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: 2003 Ford Ranger Hitch Receiver Recommendation
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Will the 6 on 5-1/2 Kodiak 12" Rotor item # KR12S Replace a 12” UFP Brake Rotor?
- Q&A: Recommended Trailer hitch Receiver For a 2008 Ford Ranger 4x4
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Trailer Hitch Receiver for 2004 Ford Ranger Edge
- Q&A: Replacement Disc Brakes, Bearings, and Actuator for 2010 EZ Loader Boat Trailer
- Q&A: How Can I Identify an Axle Without a Sticker?
- Q&A: Can a Double-Lip Trailer Hub Seal be Used in Place of a Single Lip Seal
- Article: Frequently Asked Questions About Transmission Coolers
- Article: Which Hitches are Made in the USA
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Flat Towing Package for 2008-2011 Honda CR-V
- Article: Best Bike Racks for Electric Bikes