Should the edges of CE smith post-style guide-ons for boat trailers be painted?

Question

Question:

RE: part # CE27620. e-trailer suggests painting the zinc plated guide-on struts and I was wondering what product you recommend to match the grey color of my galvanized trailer. Should I use a rust resistant primer first?

asked by: George H

0

Expert Reply:

The edges of the CE Smith Post-Style Guide-Ons for Boat Trailers # CE27620 should in fact be painted for superior protection. You can simply use a spray paint from a local hardware / paint store, or for the best protection you can start off with rust-preventive primer as you mentioned, then follow it up with a good coat of paint.

expert reply by: Andrew N

0

Answer 1

The replacement upright for your #CE27620 CE Smith 40" Post-Style Guide-Ons is #CE27608PG. The mounting hardware for the upright is #CE11452-A.

view full answer...

Answer 2

We have the CE Smith Post-Style Guide-Ons #CE27620 which are 40 inches tall like it sounds like you need. These can attach to boat frames that are up to 3 inches wide and 4-1/4 inches tall.

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Should the edges of CE smith post-style guide-ons for boat trailers be painted?

Product Page this Question was Asked From

Continue Researching