Can the Superwinch Winch 2 Go Portable Be Mounted to a Hitch Receiver

Question

Question:

I am assuming the 4000 with snatch block will pull a full size truck if not terribly stuck? Is there a receiver hitch adapter available? Thanks!

asked by: Tony

0

Expert Reply:

I do have an option for you but there isn't any receiver mount options for the Superwinch Winch 2 Go Portable part # SW1140232 since it's designed to be portable and it's a little underrated for full-size trucks. Instead, I recommend the Superwinch S5500 Trailer Winch part # SW1455201 which can be receiver mounted using a winch plate like the Curt Trailer Hitch Electric Winch Mount Plate part # C31010 and it has a higher capacity.

Please note, you'll still need to use the Superwinch Snatch Block part # SW34YR for heavier loads.

expert reply by: Conner L

0

Answer 1

The picture for determining bolt pattern is actually a little easier than maybe it seems. You just need to measure across the wheel like it shows and then count the amount of lug holes and that's all you need. So if it's 5 inches and its a 5…

view full answer...

Answer 2

Typically, we want a winch that will be used to load a car trailer to have a line pull capacity at least 50% greater than its. gross vehicle weight With that in mind, my recommendation is the Bulldog Winch Trailer Winch - Synthetic Rope - Hawse…

view full answer...

Answer 3

For a shut off switch with the Bulldog Winch part #BDW10030 I'd recommend the switch part #BDW20248 which is rated for 500 amps and is very easy to use. This is a cheap insurance policy for your winch wiring so it would be a really great…

view full answer...

Answer 4

Yes, the Superwinch Tiger Shark Series Off-Road Winch #SW1511200 that you referenced will fit the Curt Winch Mount part #C31010 that you also referenced. The winch has more capacity than the mount so you would have to stay under the 9k rating of the…

view full answer...

Answer 5

Troubleshooting electric trailer brakes is much easier if you disconnect the trailer plug from the truck and test each side separately. The process is not complicated and you need only a few items. I suggest starting on the trailer. You'll just…

view full answer...

Answer 6

We can help you select the right electric winch for your car trailer that will be able to handle the vehicle's 3500-lb weight and the slope of your trailer's loading ramp. For reference I linked an article that has great helpful information…

view full answer...

Answer 7

The Bulldog Winch part #BDW15020 would be a great option for your setup. This is a 4,400 lb 12 volt winch which uses a synthetic rope instead of a steel cable. It powers in and out and has a built in brake as well. The winch also moves at 19 feet per…

view full answer...

Answer 8

I went out to the warehouse and pulled a CURT Trailer Hitch Electric Winch Mount Plate, #C31010, to measure it. From the back of the mounting plate to the center of the nearest hitch pin hole, it is 4-1/4 inches. -The distance to the center hole is…

view full answer...

Answer 9

The pre-mounted combinations of trailer wheels and trailer tires that we offer are given a degree of balancing by the distributor but not a full dynamic balance on a balancing machine as passenger car tires require. I will explain. Wheels and tires…

view full answer...

Answer 10

I have a selection of front mount hitch mounting plates to choose from. I am including a link to a product page that will list the choices of mounting plates. Our most popular mounting plates for front mount hitch is the CURT Trailer Hitch Electric…

view full answer...

Answer 11

The Superwinch S7500 Trailer Winch #SW1475201 is designed to have more of a "universal" style for mounting and may require some adaption for installation because it does not have a typical mounting pattern. The Superwinch S7500 Trailer…

view full answer...

Answer 12

Yes, the Warn M8000 Winch uses a 10" x 4-1/2" mounting pattern which the Curt Trailer Hitch Electric Winch Mount Plate part #C31010 will accept so they can be used together just fine. The 10" x 4-1/2" mounting pattern is an…

view full answer...

Can the Superwinch Winch 2 Go Portable Be Mounted to a Hitch Receiver

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching