Where Is The Wheel Masters 4-Hose Inflation Kit Manufactured?

Question

Question:

asked by: George

1

Helpful Expert Reply:

The Wheel Masters 4-Hose Inflation Kit # WM8208 you mentioned, is manufactured in the United States.

This kit includes the bracket clamps, 4 hoses for dually tires, and 2 45° valve extenders for the front tires.

expert reply by: Bryce D

1

Answer 1

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 2

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 3

You will need the Ceiling Garnish for Fan-Tastic Vents Roof Vent #FVK1060-81 as it is specific to your Dometic Fantastic Fan 1450. The Ceiling Garnish for Ventline Roof Vent #VA0445-37 is going to have rounded corners as opposed to the square on the…

view full answer...

Answer 4

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 5

We may have a grease seal that will work in your application however, my research had conflicting measurements for the Hadco 3122 that you referenced. I contacted my technical contact at Redline to verify that the Redline Grease Seal #1105-100-031…

view full answer...

Answer 6

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 7

We have valve extenders for your dual wheel tires. I recommend the Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Wheel Cover Mount #WM8208. The length of the hoses with straight valve extenders is 13 inches. I've attached…

view full answer...

Answer 8

Thanks for the info you listed. Based on that the correct replacement motor is the part #LC295380.

view full answer...

Answer 9

In the installation instructions for the Roadmaster BrakeMaster #RM-8700 there are two fuses wired to the air compressor circuit. One 20 amp fuse on the power wire of the battery, and a 10 amp fuse connected on the blue wire that runs from the…

view full answer...

Answer 10

When you use the Wheel Masters 4-Hose Inflation Kit #WM8208 on wheels that have covers like what you send in a picture of you will have the brackets clamp to sides of rear wheels before wheel covers are installed. Basically you would install the…

view full answer...

Answer 11

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 12

Wheel Masters 4-Hose Inflation Kit #WM8208 and #WM8008 can be used with rubber valve stems. They are only increasing the length of the stems making them easier to access. They do not put any additional stress on the valve stems so they would work for…

view full answer...

Where Is The Wheel Masters 4-Hose Inflation Kit Manufactured?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching