Measurements to Top Hole on Fastway e2 Weight Distribution Shank

Question

Question:

In your answer to this question Charles S. writes ...in the position from the top to the center of the first hole is 1-11/16 inches.., but the illustration you attach shows 1- 1/16. Which is correct? Thank you.

asked by: Dan

1

Helpful Expert Reply:

On the Fastway e2 Weight Distribution Shank # FA92-02-4213 the drop position from the top to the center of the first hole is 1-11/16 inches and in the rise position the same measurement is 1-5/8 inches. Error on the picture below it is suppose to say 1-11/16 not 1-1/16.

I attached a review video link below.

expert reply by: Noah E

1

Measurements on Fastway Shank
(click to enlarge)

Answer 1

On a round bar weight distribution system like your Pro Series PS49901 you can use the Fastway e2 Shank #FA92-02-4213. It provides up to 5-1/4 inches of drop when used with a round bar system.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Hi Steve, I totally understand, as those Pro Pride hitches are great but reaaaaaaaal expensive. So we can get you weight distribution, but due to the size your hitch and weight of your trailer, there will be a cost because there are few options and…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Measurements to Top Hole on Fastway e2 Weight Distribution Shank

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching