Dust Cap Recommendation For Trailer Hub With A Diameter Of 2.44 Inches

Question

Question:

trying to locate a dust cap with the diameter of 2.444 inches

asked by: Nick

0

Expert Reply:

The Grease Cap # RG04-080 has an outer diameter of 2.441 inches and will work for your trailer hub.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

You can measure either the outer diameter of the part of the dust cap that fits into the hub OR the inner diameter of the hub where the dust cap goes using calipers such as #PTW80157. Calipers are needed because the measurement has to be as accurate…

view full answer...

Answer 2

The seals that you would need to replace your AL-KO 1536852 seals are the TruRyde Grease / Oil Seals 10-10 (Pair) - Double Lip Seals #RG06-090. They have an inner diameter of 2.125", an outer diameter of 3.376", and are used for 5,200 lb -…

view full answer...

Answer 3

According to my research the Transcom part 21334TC is an oil seal with a 2.125" inner diameter and a 3.372" outer diameter and the Transcom part 2133TB is a grease seal with a 2.125" inner diameter and a 3.376" outer diameter.…

view full answer...

Answer 4

The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 10

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 11

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 12

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Dust Cap Recommendation For Trailer Hub With A Diameter Of 2.44 Inches

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching