What Size Hitch Ball Can The Equalizer Weight Distribution System Work With

Question

Question:

This one says it comes with a 2inch ball, but can you use a 2 5/16inch ball with it instead?

asked by: Jessica

1

Helpful Expert Reply:

Yes The Equal-i-zer Weight Distribution w/ 4-Point Sway Control does come with a 2 inch ball but you can use The 2-5/16" Hitch Ball for Equal-i-zer Weight Distribution Systems # EQ91-00-6100 as well. The 2-5/16 inch hitch is sold separately.

I attached a review video link below.

expert reply by: Noah E

1

Answer 1

The Reese Strait-Line Weight Distribution system you reference, part #RP66073, is rated for a trailer tongue weight of 400-800 pounds and a gross towing weight of up to 10,000 pounds. From my on-line research I found that the 2011 Nissan Titan has a…

view full answer...

Answer 2

With all weight distribution systems including the Equal-i-zer #EQ37101ET you cannot make jackknife turns as it will either break a component of the system or one of the bars will pop out. Typically it's when people back up that there's an…

view full answer...

Answer 3

The best way to pick out a weight distribution system is to base the system you pick on the loaded tongue weight of the setup. You also need to consider the weight of any cargo behind the rear axle of the tow vehicle as tongue weight. I attached an…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 7

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 8

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 9

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 10

I attached a picture that shows how much of the etrailer.com hitch part #E98901 would hang below the rear bumper when installed.

view full answer...

Answer 11

We have confirmed that the Draw Tite part #75699 fits the 2020 Jeep Grand Cherokee Limited X which is also a fit for the SRT models. This would be the correct fit for your Limited X. I prefer this over the Curt you mentioned as it has only the hitch…

view full answer...

Answer 12

For your 2020 Jeep Grand Cherokee I recommend the Tekonsha T-One Vehicle Wiring Harness part #118727. It's custom made for your Jeep and it gives you a 4 way flat trailer connector so you have all the lights to tow a trailer safely and legally.…

view full answer...

What Size Hitch Ball Can The Equalizer Weight Distribution System Work With

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching