Is it Possible to Need a Larger Gauge Wire with the Solera 12V Electric RV Awning Conversion Kit

Question

Question:

I am going to convert my awning to 12 volt. My batteries are in the front compartment an my fifthwheel. My switch will be mounted at the rear door of my fifthwheel. The distance is about 25 is 14 gauge wire okay for that distance, or should I go 12 gauge? Thanks

asked by: Darryl P

0

Expert Reply:

When installing the Solera 12V Electric RV Awning Conversion Kit # LC434724 you will need to use 14 AWG or larger as necessary to provide 12V minimum at all times at the connection to the LCI-supplied power cable. Since you are running a longer distance, you will want to use the larger 12 gauge wiring like the 12 Gauge # 12-1-1.

expert reply by: Scott S

0

Answer 1

Some awnings have adjustments that will make the arms different lengths. This is for water run off and or to get the shade where you would like it. It seems like you have an awning like that. The Solera Awning #LC434724 has three sets of holes that…

view full answer...

Answer 2

I attached a picture of what the wax screws look like for the Solera awnings like of the #LC289561 instructions that you referenced. Basically it's under the black cap that you'll pop off and you'll unscrew that you see in the…

view full answer...

Answer 3

I checked with the manufacturer for you, and they say that the Solera Awnings are slower when they retract. If you are sure there are 12 volts by testing with a multimeter the next thing to do is ensure the pitch arms aren't bent at all,…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Is it Possible to Need a Larger Gauge Wire with the Solera 12V Electric RV Awning Conversion Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching