Are There Replacement Legs For The Lippert High-Speed Power Stabilizer Jack # LC298707

Question

Question:

We must have not fully retracted the stabilizer jack. See damage in photo. 3 options: 1. Straighten the ends. $busted knuckles 2. Replace the 2 legs if you have the replacement parts. $$ 3. Replace the whole rear stabilizer system. $$$ Thank you

asked by: Jennifer M

0

Expert Reply:

The second the legs of the Lippert High-Speed Power Stabilizer Jack # LC298707 are bent they are completely compromised and can not be trusted to hold any weight. There are no replacement legs for this system so you would unfortunately need to completely replace the entire stabilizer.

expert reply by: Kevin C

0

Bent stabilizer legs
(click to enlarge)

Answer 1

I do have a solution for you to have a working stabilizer again but unfortunately when I spoke with my contact at Lippert he said that the legs on your 198641 unit are not replaceable alone. Instead you will need to replace the whole stabilizer…

view full answer...

Answer 2

There are two replacement arms for the Lippert Components High-Speed Power Stabilizer Jacks, the Replacement Electric Stabilizer Jack Support Arm part #LC1134122 for yellow and part #LC1134121 for black. If you currently have yellow arms then you…

view full answer...

Answer 3

Yes, you can add an electric RV leveling system to a 5th wheel trailer that does not have one. Lippert's 4-Point Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 and their 6-point system #LC675817 for larger trailers provide…

view full answer...

Answer 4

In order to manually retract the legs on the Lippert Components High-Speed Power Stabilizer Jack part #LC298707 you will first need to obtain the Replacement Manual Crank Handle part #LC119226. Once you have this tool you will then need to insert it…

view full answer...

Answer 5

To determine if Lippert Components Power Stabilizer Trailer Jack Item #LC298707 will fit your 2017 Heartland Wilderness 3125BH you will need to go by the measurements compared to the available space on the trailer. This unit has an overall width of…

view full answer...

Answer 6

It sounds like you have got a good start on the troubleshooting. The next step would be to check the motor. I recommend using an alternate source to power the motor. If the motor still isn't working then it will need to be replaced. In order to…

view full answer...

Answer 7

Unfortunately, there are no replacement legs available for the Lippert Power Stabilizer Jacks like #LC298707, you'll need to replace the whole assembly. It's a good idea to replace the whole unit when there is significant damage.

view full answer...

Answer 8

The Go Power Industrial Pure Sine Wave Inverter Charger #34275013 that you referenced does have the ability to charge lithium batteries like you have. I would recommend using the custom settings like you mentioned to match just what the battery…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Are There Replacement Legs For The Lippert High-Speed Power Stabilizer Jack # LC298707

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching