Do Leaf Springs Attach to etrailer Axle e38GR Above or Below

Question

Question:

Does this sit on top of leaf springs or below. Thanks

asked by: David

0

Expert Reply:

The etrailer trailer axle part # e38GR that you referenced is underslung which means the leaf springs attach to the bottom of the axle.

expert reply by: Jameson C

0

Answer 1

There are hubs that have a 6 on 5-1/2 bolt patter that will fit a 3,500 lb axle. You won't find any for a 2k axle. The Trailer Hub and Drum Assembly #AKHD-655-35-K and Easy Grease Trailer Hub and Drum Assembly #AKHD-655-35-EZ-K both have a 6 on…

view full answer...

Answer 2

Trailer alignment starts at the trailer frame hangers and then inspecting or replacing parts. We used to have an alignment kit but the manufacturer decided not to continue it. Check the shackle strap holes first and then the hangers for elongated…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Do Leaf Springs Attach to etrailer Axle e38GR Above or Below

Product Page this Question was Asked From

Continue Researching