How to Determine if the Lippert Thin Shade Complete Window Kit Fits a 2019 KZ Connect

Question

Question:

Will this window replacement fit my 2019 kz connect?

asked by: Adam F

0

Expert Reply:

The Lippert Thin Shade Complete Window Kit # LC806621 will fit your 2019 KZ Connect as long as you have cutout dimensions of 15" wide x 24" tall and your door is 1-1/2" to 2" thick.

expert reply by: Scott S

0

Answer 1

The Lippert Thin Shade Complete Window Kit #LC806621 is designed to work with Lippert doors so if you have one on your 2019 Jayco Hummingbird then you do not have to worry about the fit. If this isn't the case, we reached out to Lippert for you…

view full answer...

Answer 2

The glass of the Lippert Thin Shade Complete Window Kit #LC806621 is tinted. See attached picture. While we don't have an install video for this exact kit I attached a video that would cover the install and show you the same process.

view full answer...

Answer 3

We do have a selection of RV Entry Door window and frame kits available and their typical size is going to be 15-1/4" x 24" to 24-3/4" tall, so there may be some slight trimming needed to get the correct fit on a new window if that…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The outer flange that sticks out to mount the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - Smoke Item #MA00-04401M is 16-1/4" x 16-1/4" so as long as you have at least 2-1/2" to 3" of space between the panel…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...