Replacement Lights For Optronics MC44, 1 Wire Lights In Red and Amber LED Lights

Question

Question:

Do you offer this light in a led version?

asked by: Dan S

0

Expert Reply:

Yes, we do have the Trailer Clearance or Side Marker Light # MC44AB1 available as an LED # MCL44AB1. This has the same 1 wire connection so the ground wire is achieved through the mounting hardware. We also have the Red LED # MCL44RB1 if you have any Red Lights MC44RB1 you would also like to replace with LED's.

expert reply by: Bud M

0

Answer 1

For a light that is similar to the Optronics MC44RB1 but has a 2-wire design you will need the following: - Optronics LED Trailer Clearance or Side Marker Light w/ Reflex Reflector - 6 Diodes - Red Lens #MCL44RB This is the same light, with exactly…

view full answer...

Answer 2

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 5

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

To replace your Phillips PC-301-A-1 Converter, I recommend the Progressive Dynamics 9300 Series RV Converter Charger #PD69RR. This is a 45 amp converter with virtually identical input/output as your old Phillips unit. You will have to add a…

view full answer...

Answer 8

The correct replacement circuit and control board for your Lippert Electronic leveling system is the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System #LC421484. This will be a plug and play solution, so…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

It appears TMW is a overseas company which I could not find much information. The 46210 is a common hub number for a 3,500lb idler hub with 5 on 4-1/2" bolt pattern. This would use either the Idler Hub #AKIHUB-545-35-G-K for standard spindles or…

view full answer...

Answer 11

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 12

If you are using either the Lippert Components Landing Gear Switch #LC145236 or the Stromberg Carlson Landing Gear Switch #LG-145236 you will connect the red wire without the fuse along with the longer black wire to the red and black wires on your…

view full answer...