Distance From Bottom of Sub Frame To Bottom Of Hitch on Curt 31374

Question

Question:

What is the dimension from the bottom of the Sub Frame plate to the bottom of the hitch?

asked by: Kyle J

0

Expert Reply:

The distance from the bottom of the sub frame, which is the same as the top of that bracket, to the bottom of the receiver on the # 31374 is 6-7/8".

expert reply by: Robin H

0

Curt 31374.
(click to enlarge)

Answer 1

The install of the Curt Hitch #31374 and the Draw Tite hitch part #65062 on your 2015 Ram 1500 are going to be so similar that you really wouldn't gain much in terms of fascia trimming/modification if you went with one or the other. The Curt…

view full answer...

Answer 2

Curt has the front hitch part #31374 as a fit for your 2016 Ram 1500 Limited with no fit exclusions for if the vehicle has air ride suspension. The same goes for the Draw Tite #65062 that you mentioned. Since you want as hidden of a hitch as possible…

view full answer...

Answer 3

There are no skid plate fit notes for the front mount hitches for your 2014 Ram 1500. That would lead me to believe that the skid plate of your truck is aftermarket. Which the best recommendation I can make would be for you to check out the install…

view full answer...

Answer 4

The Curt Front Hitch #31374 that you referenced does fit your 2021 Ram 1500 Classic and would require you to remove the tow hooks.

view full answer...

Answer 5

I checked the instruction guide for installation of the Curt Front Mount Trailer Hitch Receiver, part #31374, to your 2010 Dodge Ram 1500 4x4. The guide says that trimming the front fascia is optional but not necessary. The front fascia will flex…

view full answer...

Answer 6

When installing the Curt Front Mount Hitch #31374 on your 2018 Ram 1500, fascia trimming is optional. The fascia will flex with installation of the hitch. I will attach a diagram showing what you should cut off below of the fascia if you decide to go…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...