Ladder Roller for Yakima Crossbars

Question

Question:

Will the Rhino roller #rr13754 fit Yakima overhaul hd crossbars?

asked by: Dan

0

Expert Reply:

I have a solution for you but the Rhino Rack item # RR1375 will only fit Rhino rack cross bars. For Yakima HD Crossbars you will want the Yakima Ladder Roller item # Y01163. This ladder roller mounts to the T slot of your crossbars. It is 25-3/4" long x 4-3/4" wide x 2" tall and has a 75 lbs capacity. I have linked a review video below.

expert reply by: Jerred H

0

Answer 1

We've spoken with Furrion about your same issue with another customer and they informed us that the 88 error code on your Furrion fireplace means the blower fan is overheating. You want to make sure the inlet and outlets of the fireplace are…

view full answer...

Answer 2

I may have a solution for you, but there is not a cantilever attachment available for the Yakima Overhaul HD #Y01151-5868. There is a cantilever system on the Thule TracRac TracONE Ladder Rack w Cantilever and Toolbox Mounts for Toyota - Fixed…

view full answer...

Answer 3

We aren't aware of any changes that Yakima made to their Overhaul HD system with the part #Y01151-57 and the adapter that fits it to the Retrax rails part #Y01155 but we are aware that if you go lighter on tightening the knobs of the rack…

view full answer...

Answer 4

The Tonneau Cover Adapter Kit for Yakima OverHaul HD and OutPost HD Truck Bed Ladder Racks #Y01155 is the current version that was updated. We do not have older stock around anymore for this part number.

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the…

view full answer...

Answer 10

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...