How Are Old RV Waste Valves Removed

Question

Question:

how do I remove old valve system???

asked by: Michael L

0

Expert Reply:

You have to cut off the old valves when replacing them like with the Double RV Waste Valves - Sanitation Tee - Rotating # T18A since the solvent used to install the valves creates a permanent connection. For solvent to install the new valves we have the Valterra ABS Solvent Cement # A05-0303.

expert reply by: Jameson C

0

Answer 1

The Valterra Eccentric Tank Reducer part #T1041-1 has a 3" spigot end which installs inside the neck on the waste water tank and then a 1-1/2" hub end which you would slide a pipe into. In order to secure the spigot end into the neck on the…

view full answer...

Answer 2

What you can do is hook the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub Item #T1041-1 onto your 1-1/2" pipe using some Valterra ABS Solvent Cement - 1/4 Pint Item #A05-0303 and a hose clamp. Next…

view full answer...

Answer 3

The adapter you need is the Valterra part #T1041-1 that you referenced as it fits your configuration needs. The 3 inch portion fits into the tank and then the 1-1/2 inch portion fits over the elbow fitting like you need. Rubber cement is basically…

view full answer...

Answer 4

To attach the Valterra Eccentric Tank Reducer #T1041-1 to the rest of the plumbing on the RV and prevent leaks use the Valterra ABS Solvent Cement #A05-0303. It was made for exactly this purpose!

view full answer...

Answer 5

From what I can gather it sounds to me like you need the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub #T1041-1. The 3" Spigot mounts directly in the gray water tank outlet while the 1-1/2" Hub slides…

view full answer...

Answer 6

The Valterra Eccentric Tank Reducer, part #T1041-1, is installed with cement. When you reinstall the new one use #A05-0303. The cement is permanent so you're not going to be able to break it up. Instead you need to cut the pipes after removing…

view full answer...

Answer 7

To widen your 1-1/2" pipe to 3" using the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub #T1041-1 you would first need the Valterra DWV Adapter for RV Sewer System - ABS Plastic - 1-1/2" Hub to FPT…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

How Are Old RV Waste Valves Removed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching