Parts Needed To Change From Dual 20LB Propane Tanks to 30LB Tanks

Question

Question:

Do I need this entire kit to switch from the two 20lb propane tanks I have out for 30lb tanks?

asked by: Chad D

0

Expert Reply:

The Treaded Rod # 37207-30525 will allow you to switch the size of your propane tanks from 20lb to 30lb. The Complete Propane Tank Holder Mounting Kit # 37230WH is for applications where you are adding dual tanks or replacing everything due to damage.

You will need a new Tank Cover in White # 290-2113 to fully cover the larger tanks.

expert reply by: Bud M

0

Answer 1

The diameter of the replacement threaded rod part #37207-30525 that you referenced is 1/2 inch in diameter and has a thread pitch of 13 threads per inch.

view full answer...

Answer 2

For securing a 1,500 lb UTV like your Ranger the ShockStrap kit you'd want is the part #297-7RSBB-UTV which includes four 1,000 lb capacity ShockStraps which was designed specifically for UTV applications and would easily have the capacity needed…

view full answer...

Answer 3

The Colonial White color is being phased out so the only white lid that will fit your propane tank cover is going to be #CAM40543 which is polar white.

view full answer...

Answer 4

Typically what people do to mount the propane tank covers like the part #CAM40542 is to use a bungee cord like #EM06755 to secure it below the tanks. The cover has two tabs on the bottom of it that allow for the hooks of the strap to be attached to…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...

Answer 10

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually improves…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...

Parts Needed To Change From Dual 20LB Propane Tanks to 30LB Tanks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching