How To Measure For Replacement Support Arms For A Lippert Solera Awning On A 2022 Jayco SXL 284BHS

Question

Question:

I have a 2022 jayco 284 8lxl bhs, 12v solera awning. I am looking for support arms

asked by: Mark A

0

Expert Reply:

In order to get the correct replacement support arms for your 2022 Jayco SXL 284BHS, you will need to measure the length of your wall mount of the awning.

I have attached an image showing where you are going to need to measure.

-For 66-1/8" arms, you can use the Solera 66-1/8" Pitched Awning Support Arm # LC260294,

&

-For 69" arms, you can use the Solera 69" Standard Flat Awning Support Arm # LC281152.

expert reply by: Bryce D

0

Where To Measure For Awning
(click to enlarge)

Answer 1

The Solera Gas Strut, 124 to 144 lbs for Pitched Awning Arms #LC260282 which is 24 inches or the Solera Gas Strut 26", 124 lbs for Short and Flat Awning Arms #LC280343 are the two options we have. They are shorter than what you describe by far.…

view full answer...

Answer 2

I reached out directly to the manufacturer for you, Lippert, and what they told me was that the inner arm by itself was not something that was available as a single replacement part. What they said was that you would need to replace the whole awning…

view full answer...

Answer 3

I did check that SKU on the tag you sent and it corresponds with a pretty pricey replacement for just one and while we do not carry the exact replacement we do have another solution that you might be interested in. What you could also do if you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

How To Measure For Replacement Support Arms For A Lippert Solera Awning On A 2022 Jayco SXL 284BHS

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching