What Bolt is Needed for the Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4

Question

Question:

Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4 What size bolt do I need ?

asked by: Jon

0

Expert Reply:

The correct bolt for the Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4 # 853-5147 is the Replacement M6 x 17 mm Bolt # 924-0617-15 which is a M6 x 17 mm.

expert reply by: Scott S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 6

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 7

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 8

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 9

Both the Rhino-Rack Vortex Aero and Thule WingBar roof rack systems have very nice features and would work well for your 2014 Hyundai Santa Fe. Both systems are designed to work on vehicles that have the flush mounted rail system. As far as the…

view full answer...

Answer 10

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

What Bolt is Needed for the Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching