Clevis and Pin For Connecting Buyers 3-Point Hitch Mount To Yard Cart Trailer

Question

Question:

My yard cart has a clevis on it. Is there an attachment that would allow me to use this with a clevis hitch?

asked by: Tom A

0

Expert Reply:

The MaxxTow 2-Tang Clevis # MT70034 will allow you to attach your yard cart with the clevis to the Buyers Products Three Point Hitch Spreader Mount # 3373005345. This clevis is rated for up to 500lbs of tongue weight and up to 5,000lbs total trailer weight. You will need a Clevis Pin with Handle and Clip # C45803 if you do not already have one for your cart.

expert reply by: Bud M

0

Answer 1

On the MaxxTow 2-Tang Clevis #MT70034 the throat is 4-1/2 inches deep from the end to the weld and 3 inches from the center of the pin hole to the weld.

view full answer...

Answer 2

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

I have a solution for you. Here at Etrailer, we strongly discourage using wheel-mounted bike racks like the Kuat NV 2.0 #NV22B for bikes with fenders. Mounting wheels with fenders can cause the fenders to crack or become damaged, especially with…

view full answer...

Answer 9

The RockyMounts MonoRail bike rack you'd looked at, part #RKY10004 is a great bike rack, but it wouldn't work well with bikes that have fenders like your Aventon Aventure Fat tire ebikes. The front fender would prevent the bike…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way…

view full answer...

Answer 11

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer…

view full answer...

Answer 12

Yes, it does. The Hollywood Racks LED Light Bar item #HLY54RR is wired for a 4-way but comes with an adapter that will plug into a 7-way like yours to power the lights.

view full answer...

Clevis and Pin For Connecting Buyers 3-Point Hitch Mount To Yard Cart Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching