Replacement Circuit Board for Maxxfan 5100k RV Roof Vent

Question

Question:

Hi Would you be able to advise me on correct circuit board replacement for this Maxxair manual lift fan ? Has a reverse mode and multi speed and temperature adjustment. S/N 2017-06-5100K-A00091 Thanks

asked by: Howard

0

Expert Reply:

The correct replacement circuit board for a MaxxAir Vent Fan 5100K is the Replacement Printed Circuit Board for MaxxAir Manual Lift RV Roof Vents part # MA10A21276K.

expert reply by: Jameson C

0

Answer 1

This is more than likely a circuit board issue, and to alleviate the issue you'll just need to replace your unit's circuit board. If you have the MaxxFan Plus models: 00-04500K, 00-04700K, 00-04800K, and 00-04900K, or the MaxxFan Deluxe,…

view full answer...

Answer 2

Our part number for the 10C21275KE MaxxAir MaxxFan Circuit Board is part #MA39FR. This is for the exhaust only models like your 7501K and should get your fan back up and running. I don't know what type of troubleshooting you've done with the…

view full answer...

Answer 3

That is correct, the Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Reversible Fan #MA10A21275K is the correct replacement for your MaxxFan Deluxe Roof Vent w/ 12v Fan, Thermostat, and Remote #MA00-07500K, and will work…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Replacement Circuit Board for Maxxfan 5100k RV Roof Vent

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching