Using Hydraulic Jack Assembly for Lippert Level Up System With HWH Leveling System

Question

Question:

Can a Lippert 236560 replace a HWH model 3604 in a HWH leveling system?

asked by: Stephen F

0

Expert Reply:

The Replacement Hydraulic Jack Assembly for Lippert Level Up System, # LC99ED is not designed to be interchangeable with another manufacturers leveling system. Not that someone can't make it work by custom fabrication, but it is not designed or marketed for that purpose.

expert reply by: Michael R

0

Answer 1

I've checked with Lippert in the past and for their hydraulic leveling systems they recommend Dexron III or Mercon 5 automatic transmission fluid.

view full answer...

Answer 2

We do carry some Lippert Hydraulic jacks but none by those part numbers. I tried looking them up on Lipperts site and found nothing on the 2571254 number and the 25712510 seems to have been superseded by a jack with a 14,000 lb. capacity, but not one…

view full answer...

Answer 3

If you still continue to blow a fuse on your lading gear legs even with a new motor then that would lead me to believe you have an issue with the wiring or switch. Therefore, I recommend you trace the wires from the motor to the switch and then from…

view full answer...

Answer 4

The Replacement Hydraulic Pump Motor for Lippert Hydraulic Power Unit #LC167576 you referenced is for a different style pump and would not be a compatible replacement. The LC57AF is the correct replacement for your 414850 model pump motor. To order…

view full answer...

Answer 5

On 4-pole, 6-pole and 7-pole wiring setups the stop and turn signals are combined for each side of the vehicle. The green wire in a 4-pole typically carries both right turn and stop signals and the yellow wire carries left turn and stop. On a 6-pole…

view full answer...

Answer 6

The wheel you mentioned has a 900 lb weight rating, so the capacity will not be your problem. The wheel size is the same, but I am not entirely sure that the bolt pattern will be close enough to match up. A 4 bolt on 100mm bolt pattern would equate…

view full answer...

Answer 7

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 8

Whether or not you can flat tow with a Jeep bumper is really up to the manufacturers testing; some of the big names like MetalCloak or Poison Spyder have bumpers with D-ring attachments that can be used for flat towing connections. This is great…

view full answer...

Answer 9

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 10

The instructions for the Demco Tabless Base Plate Kit #DM77YV are being added to page but I'll also send them to you separately. In the instructions they only show that the air dam needs a chunk cut out and that the shutters would remain. The…

view full answer...

Answer 11

You have a good eye Richard, as there is not a difference between the etrailer and Demco base plates that fit your 2024 Ford Maverick: - etrailer Invisible Base Plate Kit e64FV (discontinued) - Demco Tabless Base Plate Kit #DM77YV Both will fit your…

view full answer...

Answer 12

Hi Robert; hopefully your Roadmaster tow bar is one that attaches to direct-connect base plates as opposed to crossbar base plates; for example the 8,000 lb Roadmaster Sterling would be optimal. Assuming that, here is what you need to flat tow your…

view full answer...

Using Hydraulic Jack Assembly for Lippert Level Up System With HWH Leveling System

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching