Replacement Trailer Hubs For #10 Dexter Torflex Axle With 6 on 5-1/2 Wheel Bolt Pattern

Question

Question:

I have a dexter # 4229672 3000 pound troflex axle and want to be sure the 84656UC3-EZ hubs will fit. THX

asked by: Michael R

0

Expert Reply:

Yes, the Dexter Trailer Hub and Drum Assembly # 84656UC3-EZ is the correct size for your Dexter #10 Torflex 3,000lb axle. It only differs in having the 6 on 5-1/2" bolt pattern compared to the 5 on 4-1/2" Hub # 84546UC3-EZ that came on your axle.

expert reply by: Bud M

0

Answer 1

A 3,000 lb axle is an odd size but I was able to find what you need. There isn't a kit, but you can get the bearings which are available individually. You will need bearing #LM67048 and bearing #L44649 for each hub. You will also need grease seal…

view full answer...

Answer 2

Hi Bill, The Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA92-00-0450 has a tongue weight range of 200lbs - 450lbs so you'd be right around the middle of the capacity when loaded, making this a great choice. This doesn't come with…

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

On the Jeep Wrangler and Jeep Truck models the steering wheel does not actually lock with the ignition in the off position, it just has a loss of power steering-which is likely what you're experiencing. Jeep removed the steering wheel lock from…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Hey Dave, In my opinion the etrailer Invisible Base Plate Kit #e98948 is going to be the stronger option compared to the Blue Ox Base Plate Kit #BLU53FR. Blue Ox started adding safety cables to their baseplate kits as a last resort backup in the…

view full answer...

Answer 10

Hi Dave, The etrailer Invisible Base Plate Kit #e98948 and Blue Ox Base Plate Kit #BLU53FR are designed slightly different, but both are compatible fits for your 2023 Jeep Gladiator. The #e98948 is going to be an easier installation since you…

view full answer...

Answer 11

The Westlake would be by first choice like tire part #LHWL410. This is actually a Load Range G so the capacity is 4,400-lb max load at 110 psi .This Westlake tire has a speed rating of 81 mph and also has a great warranty as well. The Taskmaster…

view full answer...

Answer 12

Yes, a total of 8 bolts secure the etrailer base plate kit part #e98948 and it is made in the USA by same company as the Demco base plate kits.

view full answer...

Replacement Trailer Hubs For #10 Dexter Torflex Axle With 6 on 5-1/2 Wheel Bolt Pattern

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching