Will The Thule Rod Vault 2 Fit 1.5" Square Crossbars

Question

Question:

Hello, I am interested in mounting this fly rod carrier to the roof of my OGT Trailer which uses 1.5inch square bars. Will this existing mounting hardware work with my crossbars? Thanks!

asked by: Christopher L

0

Expert Reply:

I had one of the Thule Rod Vault 2 Rooftop Fly Rod Carrier # TH27YV pulled from the warehouse and tested the clamps that mount it to the crossbars and found that they'll easily adjust to fit your 1.5" square crossbars. The bottom portion of the clamp is threaded so you'll be able to tighten it down the bolts using the included Allen wrench.

expert reply by: Kevin C

0

Answer 1

No, the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover #Y01151-5855 is designed to work with tonneau covers that have accessory slots for the adapters to slide into so it would not be compatible with the BAKFlip F1 Hard…

view full answer...

Answer 2

I have a possible solution for you. First, though, the Yakima OverHaul HD, part #Y01151-5855, is only compatible with Retrax XR, Pace Edwards UltraGroove, or Ford Embark LS tonneau covers. As such, you will need a different ladder rack for your…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

With the weight of your camper I recommend the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL35FJ. I prefer these as they have the internal jounce bumper which helps to reduce the bounce that is often associated with towing a trailer and…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The best air bag kit for your 2022 Ford F-350 that has a single rear wheel axle is the part #F95FV which has the 5,000 lb capacity you are wanting. Firestone bags are superior Air Lift bags. The ply rating of the rubber is higher, the attachment to…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...