Inner Channel Width of Lock N Roll Articulating Hitch # 336VS503

Question

Question:

What is the inside dimensions of the channel mount? I saw the outside dimensions are 3 inches.

asked by: Daniel J

0

Expert Reply:

The inner channel width of the Lock N Roll Articulating Hitch # 336VS503 that you referenced is 2-7/8 inches on the side that attaches to the articulating mount. The other end is designed to fit into a 3 inch wide channel. The inner width of this would then be 2-1/2 inch.

expert reply by: Jameson C

0

Answer 1

The Lock N Roll #336VS517 has a rise or drop of 4 1/2", and the Lock N Roll ##336VS503505 has a rise or drop of 4 1/4". The main difference between the 2 Lock N Roll hitches #336VS503505 and #336VS517 is that the #336VS503505 is adjustable.…

view full answer...

Answer 2

I spoke with my contact at Lock N Roll about the Lock N Roll Articulating Hitch part #336VS503505 and they were not quite sure what measurements you are looking for nor was I. That said, I went out to our warehouse for you and jotted down a few…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

Since the discontinued MaxxAir 4700k model fits a standard 14 x 14 RV vent opening, I recommend the MaxxFan Plus Roof Vent w/ 12V Fan - 10 Speed #MA00-04500K. The MaxxFan Plus comes with a thermostat and a remote for easy temperature customization.…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Inner Channel Width of Lock N Roll Articulating Hitch # 336VS503

Product Page this Question was Asked From

Continue Researching