Reverse Lockout Pin For A Dexter TDE 85LP Brake Actuator

Question

Question:

I want to order the reverse lockout pin for a model TDE lp85. Does this pin work?

asked by: Mike S

0

Expert Reply:

The Replacement Damper Pin for Titan Model 10 Brake Actuator # T1593400 that you mentioned is actually meant to work with the Titan Model 10 surge-type brake actuators, however I spoke with Dexter, and they informed me that for your TDE 85LP brake actuator you can use the:

-Replacement Hitch Pin Kit for Dexter Axle Brake Actuators # DX89XR.

expert reply by: Bryce D

0

Answer 1

Your description of your trailer setup indicates that your surge coupler has an electric lockout feature to allow you to reverse the trailer without the surge brakes engaging. Some surge couplers use a manual lockout but yours has a solenoid with two…

view full answer...

Answer 2

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 3

The solenoid on the Demco Hydraulic Brake Actuator w Drop and Electric Lockout #DM8164311 will have two wires coming out of it, a ground wire and a power wire. You'll need to connect he power wire to the reverse circuit on the trailer connector.…

view full answer...

Answer 4

The backup light circuit of a vehicle would provide enough amperage to activate the lockout solenoid on a trailer with surge brakes. I'd make sure that the extra blue wire of your #47515 does have voltage when the reverse lights are on to verify…

view full answer...

Answer 5

The Demco Hydraulic Brake Actuator w Drop and Electric Lockout #DM8164311 is rated for disc brakes and it has the electric lockout so as far as compatibility goes those parts will match up. What you need to check on is the mounting bolt hole pattern.…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Reverse Lockout Pin For A Dexter TDE 85LP Brake Actuator

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching