Can 2” Hitch Ball With 1" Diameter Shank Be Replaced With 2-5/16" Hitch Ball

Question

Question:

Can I replace my 2” hitch ball with a 2 5/16” ball without replacing the hitch ? Does the larger ball have the same shaft diameter? Thank you.

asked by: Chaz

1

Helpful Expert Reply:

As long as you use the same diameter shank you can definitely replace your 2" ball. I recommend the 2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs # C40005. Since this has the same 1" diameter shank you will not have an issue using it with your existing ball mount. This ball has a 7,500 lb capacity and comes with a 1 year warranty.

expert reply by: Robin H

1

Ball Mount Shank Diameter.
(click to enlarge)

Answer 1

The two sizes you mentioned are different balls. The larger size typically has higher capacities and fits couplers that are designed for it's size. The 2 inch size is typically seen in lighter duty applications. You have to match the correct…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Can 2” Hitch Ball With 1" Diameter Shank Be Replaced With 2-5/16" Hitch Ball

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching